10' x 8' Model CF10 Concession Trailer

Standard Specifications

10' x 8' Model CF10 Concession Trailer
All STEEL Unibody Construction

Body Length

• 10 Feet

Overall Width

• 8 Feet

Inside Height

• 83"

Outside Height

• 96"

Axles

• Heavy-Duty Commercial Quality
• One 3,500 Pound Capacity

Suspension

• Single 3-Leaf Springs

Wheels

• 15" By 6" One-Piece 5 Hole With 4-1/2" Bolt Circle

Tires

• P225/75R 15" Radial Whitewalls

Brakes

• Electric Drum Type On All Wheels
• 12 Volt, 10" By 2-1/4"
• Breakaway Switch Wired In
• Require Tow Vehicle Controller - Not Supplied With Trailer

Front Jack

• 3,000 Pound Sidewind Type Recessed In Front Bumper
• Sand Flange

Rear Jacks

• Two Fold-Up Stabilizing Jacks Mounted To Frame Under Floor

Countertops

• 16" Deep Painted Steel
• Across Both Sides And Rear Of Trailer
• 25' Total Length
• Depth Modified For Factory-Installed Options

Counter Height

• 34" Inside
• 47" Outside

Overhead Shelves

• 9" Wide Painted Steel
• Located Above Both Side Serving Windows
• 20' Total Length

Lights/Brakes Receptacle

• 6-Way 12 Volt

G.V.W.R.

• 3,600 Pounds

Scale Weight

• 2,580 Pounds

Tongue Weight

• Maximum 360 Pounds - 10% of Gross Weight

Payload Capacity

• Maximum 1,020 Pounds

Hitch Height

• Approximately 18.5" To Top of Ball - Varies With Amount Of Load

Frame

• Heavy-Duty All Welded Tubular Steel

Body Construction

• Welded 14 Gauge Formed Steel
• Integral Counters

Roof

• Welded 14 Gauge Formed Steel with Crossbreak and Silicone Seal
• Mansard Style

Lift-Up Awnings for Serving Openings

• 16 Gauge Steel With Outward Crossbreak
• Two 38" By 112" (Sides)
• One 38" By 82" (Rear)

Swing-Out Awning Supports

• 3/4" Steel Rod With Rubber Tips to Protect Finish

Entrance Door

• 16 Gauge Steel With Outward Crossbreak
• One 25" By 70" With Outward Crossbreak
• Chrome "T" Handle With Lock And Key

Floor

• 1/8" Steel Safety Treadplate
• 4" Drop Construction For Low 13" Inside Floor Height

Hitch

• Forged Steel 2" Ball Coupler
• Positive Lock Collar and Pin

Tongue

• 3" Square Tube Steel
• Removable By Pulling One Hitch Pin

Road Lights

• Sealed Beam Type
• Meet DOT/ICC Requirements
• Wiring Run Through Frame and Steel Conduit For Protection

Paint

• Two Coats Of White Acrylic Enamel
• Corrosion Resistant Primer

Trim

• Chrome Hub Caps
• Chrome Wheel Well Edge Guard

Inside Lighting

• One 120 Volt Fluorescent Fixture
• Two Dual Pin 40 Watt, 48" Fluorescent Bulbs
• Mounted Above Entrance Door
• Controlled By Wall-Mounted Switch

Inside Electrical

• Two Three-Prong 15 Amp, 120 Volt Duplex Receptacles
• 15 Amp Male Motor Base Plug Mounted On Outside
• Load Center And 15 Amp Breaker
• All Components UL Listed
• Installed In Accordance With The National Electrical Code

Cleanup

• All-Metal Construction
• Two Drainholes In Rear Provide For Quick And Easy Washout