14′ x 8′ Model CF14 Concession Trailer - Specifications

Standard Specifications

14′ x 8′ Model CF14 Concession Trailer
All STEEL Unibody Construction

Body Length

• 14 Feet

Overall Width

• 8 Feet

Inside Height

• 83″

Outside Height

• 96″

Axles

• Heavy-Duty Commercial Quality
• Two 3,500 Pound Capacity

Suspension

• Tandem 4-Leaf Springs

Wheels

• 15″ By 6″ One-Piece 5 Hole With 4-1/2″ Bolt Circle

Tires

• P225/75R 15″ Radial Whitewalls

Brakes

• Electric Drum Type On All Wheels
• 12 Volt, 10″ By 2-1/4″
• Breakaway Switch Wired In
• Require Tow Vehicle Controller - Not Supplied With Trailer

Front Jack

• 5,000 Pound Sidewind Type Recessed In Front Bumper
• Sand Flange

Rear Jacks

• Two Fold-Up Stabilizing Jacks Mounted To Frame Under Floor

Countertops

• 16″ Deep Painted Steel
• Across Both Sides And Rear Of Trailer
• 33′ Total Length
• Depth Modified For Factory-Installed Options

Counter Height

• 34″ Inside
• 47″ Outside

Overhead Shelves

• 9″ Wide Painted Steel
• Located Above Both Side Serving Windows
• 28′ Total Length

Lights/Brakes Receptacle

• 6-Way 12 Volt

G.V.W.R.

• 5,000 Pounds - with standard 2″ ball coupler
  Optional 2-5/16″ ball coupler increases G.V.W.R. to 7,200 pounds.

Scale Weight

• 3,450 Pounds

Tongue Weight

• Maximum 720 Pounds - 10% of Gross Weight

Payload Capacity

• Maximum 1,550 Pounds - with standard 2″ ball coupler
  Optional 2-5/16″ ball coupler increases payload capacity to 3,750 pounds.

Hitch Height

• Approximately 18.5″ To Top of Ball - Varies With Amount Of Load

Recommended Tow Vehicle

• 1/2 Ton Truck or Van with V-8 Engine Minimum
  (larger than 1 Ton requires AIRSAFE™ or equivalent air ride hitch)

Frame

• Heavy-Duty All Welded Tubular Steel

Body Construction

• Welded 14 Gauge Formed Steel
• Integral Counters

Roof

• Welded 14 Gauge Formed Steel with Crossbreak and Silicone Seal
• Mansard Style

Lift-Up Awnings for Serving Openings

• 16 Gauge Steel With Outward Crossbreak
• Two 38″ By 112″ (Sides)
• One 38″ By 82″ (Rear)

Swing-Out Awning Supports

• 3/4″ Steel Rod With Rubber Tips to Protect Finish

Entrance Door

• 16 Gauge Steel With Outward Crossbreak
• One 25″ By 70″ With Outward Crossbreak
• Chrome "T" Handle With Lock And Key

Floor

• 1/8″ Steel Safety Treadplate
• 4″ Drop Construction For Low 13″ Inside Floor Height

Hitch

• Forged Steel 2″ Bulldog™ Brand Ball Coupler
• Positive Lock Collar and Pin

Tongue

• 3″ Square Tube Steel
• Removable By Pulling One Hitch Pin

Road Lights

• Sealed Beam Type
• Meet DOT/ICC Requirements
• Wiring Run Through Frame and Steel Conduit For Protection

Paint

• Two Coats Of White Acrylic Enamel
• Corrosion Resistant Primer

Trim

• Chrome Hub Caps
• Chrome Wheel Well Edge Guard

Inside Lighting

• One 120 Volt Fluorescent Fixture
• Two Dual Pin 32 Watt, 48″ Fluorescent Bulbs
• Mounted Above Entrance Door
• Controlled By Wall-Mounted Switch

Inside Electrical

• Two Three-Prong 15 Amp, 120 Volt Duplex Receptacles
• 15 Amp Male Motor Base Plug Mounted On Outside
• Load Center And 15 Amp Breaker
• All Components UL Listed
• Installed In Accordance With The National Electrical Code

Cleanup

• All-Metal Construction
• Two Drainholes In Rear Provide For Quick And Easy Washout