|
Standard Specifications
16′ x 8′ Model CF16 Concession Trailer
All STEEL Unibody Construction
Body Length
Overall Width
Inside Height
Outside Height
Axles
- Heavy-Duty Commercial Quality
- Two 3,500 Pound Capacity
Suspension
Wheels
- 15″ By 6″ One-Piece 5 Hole With 4-1/2″ Bolt Circle
Tires
- P225/75R 15″ Radial Whitewalls
Brakes
- Electric Drum Type On All Wheels
- 12 Volt, 10″ By 2-1/4″
- Breakaway Switch Wired In
- Require Tow Vehicle Controller - Not Supplied With Trailer
Front Jack
- 5,000 Pound Sidewind Type Recessed In Front Bumper
- Sand Flange
Rear Jacks
- Two Fold-Up Stabilizing Jacks Mounted To Frame Under Floor
Countertops
- 16″ Deep Painted Steel
- Across Both Sides And Rear Of Trailer
- 37′ Total Length
- Depth Modified For Factory-Installed Options
Counter Height
Overhead Shelves
- 9″ Wide Painted Steel
- Located Above Both Side Serving Windows
- 32′ Total Length
Lights/Brakes Receptacle
G.V.W.R.
- 7,200 Pounds - with 2-5/16″ ball coupler only
Scale Weight
Tongue Weight
- Maximum 720 Pounds - 10% of Gross Weight
Payload Capacity
- Maximum 3,250 Pounds - with 2-5/16″ ball coupler only
Hitch Height
- Approximately 18.5″ To Top of Ball - Varies With Amount Of Load
Recommended Tow Vehicle
- 1/2 Ton Truck or Van with V-8 Engine Minimum
(larger than 1 Ton requires AIRSAFE™ or equivalent air ride hitch)
Frame
- Heavy-Duty All Welded Tubular Steel
Body Construction
- Welded 14 Gauge Formed Steel
- Integral Counters
Roof
- Welded 14 Gauge Formed Steel with Crossbreak and Silicone Seal
- Mansard Style
Lift-Up Awnings for Serving Openings
- 16 Gauge Steel With Outward Crossbreak
- Four 38″ By 90″ (Sides)
- One 38″ By 82″ (Rear)
Swing-Out Awning Supports
- 3/4″ Steel Rod With Rubber Tips to Protect Finish
Entrance Door
- 16 Gauge Steel With Outward Crossbreak
- One 25″ By 70″ With Outward Crossbreak
- Chrome "T" Handle With Lock And Key
Floor
- 1/8″ Steel Safety Treadplate
- 4″ Drop Construction For Low 13″ Inside Floor Height
Hitch
- Forged Steel 2-5/16″ Bulldog™ Brand Ball Coupler
- Positive Lock Collar and Pin
Tongue
- 3" Square Tube Steel
- Removable By Pulling One Hitch Pin
Road Lights
- Sealed Beam Type
- Meet DOT/ICC Requirements
- Wiring Run Through Frame and Steel Conduit For Protection
Paint
- Two Coats Of White Acrylic Enamel
- Corrosion Resistant Primer
Trim
- Chrome Hub Caps
- Chrome Wheel Well Edge Guard
Inside Lighting
- Two 120 Volt Fluorescent Fixtures
- Four Dual Pin 32 Watt, 48" Fluorescent Bulbs
- Mounted Above Entrance Door and Above Rear Counter
- Controlled By Wall-Mounted Switch
Inside Electrical
- Two Three-Prong 15 Amp, 120 Volt Duplex Receptacles
- 15 Amp Male Motor Base Plug Mounted On Outside
- Load Center And 15 Amp Breaker
- All Components UL Listed
- Installed In Accordance With The National Electrical Code
Cleanup
- All-Metal Construction
- Two Drainholes In Rear Provide For Quick And Easy Washout
|
|